4” RED FLUSH-MOUNT TAIL LIGHT
4” AMBER FLUSH-MOUNT TAIL LIGHT
93228
93229
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
9. Do not allow children to play with the Flush Mount Tail Light.
10. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.
11. Make certain to follow all local laws regarding vehicles and Tail Lights.
12. Do not cut or rewire any part of the Tail Light.
13. Make certain the vehicle is turned off before doing any maintenance.
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your 4” Flush-Mount Tail Lights, check to make sure that all parts listed in the parts
list on page 4 are included. If any parts are missing or broken, please call HARBOR FREIGHT
TOOLS at 1-800-444-3353.
Assembly
Your 4” Flush-mount Tail Lights will require complete installation. It is important that you read the
entire manual to become familiar with the product BEFORE you install and use the 4” Flush-Mount
Tail Lights. Before operating this product be sure that you have all parts described in the Parts List
and Assembly Diagram located on page 4 of this manual. If you do not have experience doing this
type of electrical work, the job should be done by an automotive service technician.
1. Make certain that the vehicle’s engine is OFF before doing any maintenance. Proceed with the
following steps for installing the 4” Flush-mount Tail Lights.
2. Use a pin connector or inline splice connector (both not included) to connect the Tail Lights to
your vehicle. When using an inline splice connector, it is not necessary to strip the wires.
3. Insert two positive wires to the appropriate wires in your vehicle’s lighting system. Insert one
wire from your vehicle into one channel of the inline splice connector. Insert the wire from the
Tail Light into the second channel of the inline splice connector. Fold down the tab on the inline
splice connector to make the connection. Insert the second wire in the same fashion.
4. Make certain that the black wire is connected to metal on the vehicle to provide a ground.
SKU 93228 / 93229
For technical questions please call 1-800-444-3353.
Page 3
Installing the Light Bulb
1. Use a light bulb of the type described on page 2. Gently grasp and twist the Bulb Housing (2)
and pull it out from the main Tail Light (1) - see Figure 1.
Figure 1
Bulb Housing (2)
2. Line up pins on the light bulb with the grooves on the Bulb Housing (2) and slide the Light Bulb
into place.
3. Verify that the Light Bulb is securely in place. Thread the Bulb Housing back into the main Tail
Light (1).
Note: When mounting the Tail Lights to a trailer, both the forward amber and the rear red Tail
Lights are connected to the trailer’s tail light wires.
4. Once the wires are properly connected, test them before setting the Tail Light in place.
5. To mount onto a trailer or vehicle, use all three screw holes in the Tail Light Cover to secure it in
place. Mounting hardware is not included with the Flush-Mount Tail Light. Note that the Amber
Tail Light is mounted to the front of the vehicle, and the Red Tail Light is to be mounted to the
rear of the vehicle.
Parts List
Part # Description
Qty.
1
1
1
2
MainTail Light
Bulb Housing
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KINDTO THE BUYERTHAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
SKU 93228 / 93229
For technical questions please call 1-800-444-3353.
Page 4
|