Cannon All in One Printer C5051 User Manual

September 24, 2009  
Revision 0  
C5051/C5045/C5035/C5030 Series  
imageRUNNER ADVANCE  
Service Manual  
Product Outline  
Function  
Periodic Servicing  
Parts Replacing and Cleaning  
Adjustments  
Troubleshooting  
Error Code  
Service Mode  
Installation  
Appendix  
 
1 2 3 4 5 6 7 8 9  
fineline6  
0-3  
The following rules apply throughout this Service Manual:  
Explanation of Symbols  
The following symbols are used throughout this Service Manual.  
1. Each chapter contains sections explaining the purpose of specific functions and the  
relationship between electrical and mechanical systems with reference to the timing of  
Symbols  
Explanation  
Symbols  
Explanation  
operation.  
In the diagrams,  
represents the path of mechanical drive; where a signal name  
Check.  
Remove the claw.  
accompanies the symbol, the arrow  
indicates the direction of the electric  
signal.  
F-0-1  
F-0-2  
The expression "turn on the power" means flipping on the power switch, closing the  
front door, and closing the delivery unit door, which results in supplying the machine with  
power.  
Check visually.  
Insert the claw.  
F-0-3  
F-0-5  
F-0-4  
F-0-6  
Check the noise.  
Use the bundled part.  
Push the part.  
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is  
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from  
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD  
signal goes on when '0'.  
Disconnect the connector.  
Connect the connector.  
In practically all cases, the internal mechanisms of a microprocessor cannot be checked  
in the field. Therefore, the operations of the microprocessors used in the machines  
are not discussed: they are explained in terms of from sensors to the input of the DC  
controller PCB and from the output of the DC controller PCB to the loads.  
F-0-7  
F-0-8  
Plug the power cable.  
Turn on the power.  
F-0-9  
F-0-10  
F-0-12  
Remove the cable/wire  
from the cable guide or wire  
saddle.  
The descriptions in this Service Manual are subject to change without notice for product  
improvement or other purposes, and major changes will be communicated in the form of  
Service Information bulletins.  
F-0-11  
F-0-13  
F-0-14  
F-0-15  
All service persons are expected to have a good understanding of the contents of this Service  
Manual and all relevant Service Information bulletins and be able to identify and isolate faults  
in the machine.  
Set the cable/wire to the  
cable guide or wire saddle.  
Remove the screw.  
Tighten the screw.  
0-3  
 
fineline6  
CDRH Act  
Laser Safety  
Handling of Laser System  
Turn power switch ON  
Safety of Toner  
imageRUNNER ADVANCE  
C5051/5045/5035/5030  
Series  
Notes When Handling a  
Lithium Battery  
Notes Before Servicing  
 
fineline6  
0
0-2  
CDRH Act  
Handling of Laser System  
The Center for Devices and Radiological Health of the US Food and Drum Administration put  
into force regulations concerning laser products on August 2, 1976. These regulations apply  
to laser products manufactured on and after August 1, 1976, and the sale of laser products  
not certified under the regulations is banned within the Untied States. The label shown here  
indicates compliance with the CDRH regulations, and its attachment is required on all laser  
products that are soled in the United States.  
When servicing the area around the laser assembly, be sure to turn off the main power.  
The machine's covers that can reflect laser light are identified by means of a warning label  
(Figure). If you must detach a cover showing the label, be sure to take extra caution during  
the work.  
CANON INC.  
30-2,SHIMOMARUKO,3-CHOME,OHTA-KU,TOKYO,JAPAN  
MANUFACTURED:  
THIS PRODUCT CONHORMS WITH DHHS RADIATION  
PERFORMANCE STANDARD 21CFR CHAPTER 1  
SUBCHAPTER J.  
F-0-16  
A different description may be used for a different product.  
F-0-17  
Laser Safety  
Laser beam radiation may pose a danger to the human body. A laser scanner mounted on the  
machine is sealed with the protection housing and external cover to prevent the laser beam  
from leaking to the outside. The laser beam never leaks out of the scanner as far as users  
operate the machine normally.  
0-2  
 
0
fineline6  
0
0-3  
Turn power switch ON  
Safety of Toner  
The machine is equipped with 2 power switches: main power switch and control panel power  
About Toner  
switch.  
The machine goes on when the main power switch is turned on (i.e., other than in low power  
mode, sleep mode).  
The machine's toner is a non-toxic material made of plastic, iron, and small amounts of dye.  
Do not throw toner into fire. It may cause explosion.  
If your clothing or skin has come into contact with toner, wipe it off with tissue; then, wash it  
off with water.  
Do not use warm water, which will cause the toner to jell and fuse permanently with the  
fibers of the cloth.  
Tonner is easy to react with plastic material, avoid contact with plastic.  
0-3  
 
0
fineline6  
0
0-4  
Notes When Handling a Lithium Battery  
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.  
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  
The following warnings are given to comply with Safety Principles (EN60950).  
Wenn mit dem falschen Typ ausgewechselt, besteht Explosionsgefahr.  
Gebrauchte Batterien gemäß der Anleitung beseitigen.  
Notes Before Servicing  
At servicing, be sure to turn OFF the power source according to the specified steps and  
disconnect the power plug.  
0-4  
 
0
fineline6  
Product Overview  
1
Product Lineup  
Feature  
Specifications  
Name of Parts  
 
1
fineline6  

Belkin Switch F1DN104E User Manual
Black Decker Blender BLM7600G User Manual
Blanco Indoor Furnishings 501 110 User Manual
Bosch Appliances Ventilation Hood DAH93 User Manual
Bravetti Food Processor BP100 User Manual
Campbell Hausfeld Air Compressor VT640700 User Manual
Canon Digital Camera 0134C001 User Manual
Canon IP Phone INDEX 4602 User Manual
Carrier Heat Pump 50PQ User Manual
Char Broil Gas Grill 463741510 User Manual